In order for the dishwasher to be able to do its job properly in the household, a few procedures must be observed. If the machine is used frequently, it also requires regular care to prevent malfunctions or failures.
Washing dishes in the household is often very annoying, but there is a dishwasher that does its job reliably. Such a device is a real work-saver, especially for families with several children. Since the dishwasher is used often, errors or problems can occur during use. Most of the time, these are small things that you can fix yourself without hiring an expensive repair service.
The built-in heater is defective
If you notice that the dishwasher only works in the cold mode for the respective washing processes, something is wrong. Either the heater is defective or the built-in thermostat. In order to repair this, the necessary spare parts are required. Before doing this yourself, the mains plug should be pulled out of the device and the device should be disconnected from the existing water connection. The components to be replaced must fit the respective device exactly. Exact information can often be found in the user manual.
Water is no longer pumped out
If the water is no longer pumped out properly after the rinsing process, this makes a bad impression at first. But in most cases, this problem can be fixed quite easily. To do this, the existing sieve should first be checked at the outlet in the machine. This can be taken out easily. If it is clogged, cleaning must be done. Another cause can be a kinked drain hose. This should then be straightened again so that the water can drain properly. If this was not the cause either, there may be a defect in the drain pump. This must then be replaced with a new component.
The dishwasher cannot be opened
A very common source of error is that the machine door can no longer be opened. There can be several possible reasons for this. It is possible for the child safety lock to be switched on automatically. A defect in the door lock can also be present here. To deactivate the child lock, the programming must be changed accordingly. It can also help to switch the device off and on again. If, on the other hand, there is a defect in the door lock, it must be repaired accordingly.
Flashing error message
If a flashing error message suddenly lights up on the device, this is often not a very big problem, in most cases, it is necessary to fill in a new rinse aid or appropriate special salt. The error messages can vary depending on the manufacturer. The operating instructions provide a very good overview, where the exact meaning of the symbols is explained and what needs to be done afterward.
Clean rinsing is no longer possible
If the dishwasher is no longer able to wash the dishes absolutely clean, thorough cleaning of the sieve and the spray arm is usually necessary. If there is a blockage, the functionality is significantly reduced and a clean flushing process cannot take place. In addition, there can be an unpleasant smell in the dishwasher. The sieve only needs to be removed from the bottom and cleaned by hand. The spray arm can usually be easily removed and the dirt can be carefully removed. However, if limescale deposits or a fairly gray tinge have formed on the dishes, this can indicate a lack of salt. There is usually a defect in the ion exchanger.
No more water is drawn in
If the dishwasher is no longer able to draw in water, it does not always have to be a fault in the device. It is also possible that there is a defect in the faucet. To do this, the water tap should first be turned off and the hose removed from the machine.
There is usually a strainer at the top of the hose which could be clogged. If this is not the case, the faucet should still be checked again by placing a bucket under it. If only a few drops of water come out after activation, it is advisable to call an installer for help. He can check the line carefully and insert a new faucet if necessary.
Detergent is too old
A big mistake is often made when buying dish soap in very large bottles. Buying in advance is not a good idea, because the longer the dishwashing detergent is stored, the more the enzymes it contains break down. These are absolutely important so that the dishes can be washed thoroughly.
After just a few months, the cleaning performance decreases significantly and the dishes are no longer really clean. If, on the other hand, the dishes come out of the dishwasher very cloudy, this is usually due to the degree of hardness and lime content of the water. Here it depends on the right dosage of the detergent used. It can also be useful here to descale the dishwasher. Natural home remedies will help you with this.
